White Ice 510FG: Food Grade Heat Sink Compound

Product Description:

White Ice 510FG is a Non-Reactive, Silicone, Thermally Conductive food grade thermal grease with low thermal resistance and a soft, non-flowable consistency. This product is formulated with FDA (Food & Drug Administration) approved ingredients in compliance with CFR, Title 21 paragraph 178.3570 of the FDA guidelines and NSF Registered. This product is acceptable as incidental food contact for use in and around food processing areas.

Key Features and Benefits:

• Good Thermal Performance- ( 0.80 W/m °k)
• Low Interface Thermal Resistance. – ( 0.05 °C-In² /W)
• Thin Bond lines to ≤1 mil
• Low bleed and evaporation
• Non-Toxic/ NSF Registered
• Re-workable/Easy to Remove
• Easy to Apply by Dispensing or Screen Printing/Stencil

Typical Applications:

White Ice 510FG Heat Sink Compound is applied to the any electronic devices for heat transfer which is located in and around food processing areas. Also industrial applications include mounting studs of transistors, diodes and silicone controlled rectifiers. In these situations, a small amount of the thermal grease is applied using screen printing/stencil methods. It is also used in mounting semiconductor devices; thermoelectric modules; power transistors and diodes; coupling entire heat generating assemblies to chassis; heat transfer medium on ballasts; thermal joints; thermocouple wells; mounting power resistors; and for any devices where efficient cooling is required in major industries including, electronic (computer, appliance, wireless, etc.), automotive and electrical.

Close

Red Ice: High Temperature Thermal Compounds

Product Description:

Red Ice 600 series are high temperature stable thermal greases engineered with special aero space fluid technology to eliminate compound "dry out" problems due to continuous operating temperature above 200 °C. This series of thermal compounds has shown outstanding heat transfer and high temperature stability for all types of electronic and industrial applications. Recommended for aero space application because of low to zero out gassing, No dry out.

Typical Applications:

Aero Space applications, Heater cartridges, Thermistors, RTD, Thermocouple wells, Portable heaters and Tank heaters.

Most Popular Products:

• Red Ice 611HTC: High thermal conductivity with high temperature stability. Rated up to 360 °C. Meets NASA out gassing requirements.
• Red Ice 611: Low Thermally Conductive with high temperature stability. Rated up to 360 °C. Meets NASA out gassing requirements. Commonly used between heating element and plate.
• Red Ice 613: Low cost solution for high temperature application, Rated up to 250 °C.

Close

Black Ice and Silver Ice: Electrically Conductive Compounds

Product Description:

Black Ice 700 series are electrically and thermally conductive greases engineered with highly conductive fillers and silicone/non silicone fluids. Excellent wetting and spreadability with screen printable consistency. The 700 series is ideal for low power applications that require static drain, grounding, and soft electronics connection. High thermal conductivity ratings up to 7 W/mºK are readily available.

Typical Applications:

High power electrical applications, Power switches, Circuit breakers, Grounding semiconductor components and high power cpu to heat sink.

Most Popular Products:

• Silver Ice 710 & 710NS: Pure silver fortified thermal greases, non curable system. Thermal conductivity of 7 W/mºK. Direct replacement of “Arctic Silver” products. Recommend for high heat flux & thin film applications.
• Black Ice 711: Low cost solutions for electrical contact applications.

Close

EJC: Electrical Joint Compounds

Product Description:

TIM-Electrical Joint Compounds (EJC) is specially formulated with latest technology to prevent oxide film formation on metal surfaces and prevents corrosion. It offers superior weathering characteristics over wide temperature ranges, and provides highly conductive tight joints. Proprietary filler particles help in penetrating oxide films and act as electrical bridges between conductor strands, aid in gripping conductor, improve electrical conductivity and enhance integrity of the connection.

Surface contamination, especially surface oxide, must be expected on all conductors, these surface oxide films are insulators and must be broken down to achieve the metal-to-metal contact required for efficient electrical connections. Aluminum oxide, in particular, forms very rapidly; therefore, aluminum conductors must be thoroughly cleaned by use of an emery cloth prior to making the connection, In addition to cleaning, surface should be covered with joint compound to exclude moisture, thus preventing the oxide from reforming

Most Popular Products:

• EJC 744: Gritted electrical joint compound is recommended for all aluminum and copper compression connections. It is not recommended as lubricant on threaded fittings.
• EJC 745NS: Non-gritted Non-Silicone electrical joint compound recommended for No-Drip application for aluminum and copper connectors.
• EJC 745SL: Non-gritted Silicone electrical joint compound recommended for rigid bus connection, bolted flat-pad connection between aluminum and aluminum and copper applications.

Close

Blue Ice: Non Silicone Thermal Compounds

Product Description:

Blue Ice 400 series are unique synthetic thermal greases engineered to provide low bleed and oil migration to prevent component contamination associated with silicone greases. They offer superior thermal conductivity and low thermal resistance with long term stability.

Typical Applications:

CPU to Heat sink, Transistors, Diodes, IGBTs, Rectifiers, TEC modules, telecommunication hardware etc.

Most Popular Products:

• Grey Ice 4100: High thermal conductivity/Low resistance/Thin bond line thickness.
• Blue Ice 411: Direct replacement of standard silicone grease (Dow 340).
• Blue Ice 425: Engineered to clean easily with water or aqueous detergent cleaning solutions, thus eliminating the use of a flammable solvent.

White Ice: Silicone Thermal Compounds

Product Description:

White Ice 500 series are silicone based thermal greases engineered with special binding agents to reduce bleed and oil separation. These compounds offer excellent wetting properties, spreadability and the low viscosity formulation makes them easy to apply to thin bond line thickness for minimum thermal resistance. Timtronics silicone compounds offer superior conductivity, low thermal resistance and long term stability.

Typical Applications:

CPU to Heat sink, Transistors, Diodes, IGBTs, Rectifiers, TEC modules, Telecommunication hardware, Thermistors, RTD and Thermocouple wells.

Most Popular Products:

• Grey Ice 5100: High thermal conductivity/Low resistance/Thin bond line thickness.
• White Ice 510: Standard silicone thermal grease, direct replacement of Dow 340 and Wakefield 120.
• White Ice 512: Low cost, high thermally conductive grease.

Close

TIM-800: Thermally Conductive Epoxies/Adhesives

Product Description:

TIM-800 series are thermally conductive, electrically insulating epoxies engineered with highly conductive ceramic fillers and non silicone resins. They are designed for the demanding needs of die-attach heat sink bonding and surface mount applications. Rapid heat transfer properties eliminate hot spots and the low epoxy shrinkage factor minimizes the risk of damage to fragile components, resulting in increased operating efficiencies. Available in one part, two parts, heat curable and room temperature cure systems.

Typical Applications:

Fabricating heat sink, bonding semiconductors, substrate attach, lid seal, SMD attach, stacking components and die attach applications.

Most Popular Products:

• TIM-813: One part heat cure system, excellent conductivity and bond strength at high temperature.
• TIM-818: High strength, thermally conductive adhesive, flash cure in 5 minutes. No mix, two part system to replace mechanical clips, fasteners or tapes in securing heat generating devices and heat sink.

Electrically Conductive

Product Description:

Electrically conductive adhesives are designed with pure silver and resin and are typically used for microelectronic applications. All products feature very high purity, low ionic content, wide operating temperature range and excellent electrical conductivity even after exposure of 1000 hours at 150°C.

Typical Applications:

Die-attach, chip bonding, cold soldering and other micro electronics bonding applications.

Thermally Conductive
Potting Compounds (TIM-PC Series)

Product Description:

TIM-PC series are pourable, filled epoxy resin systems offering excellent heat transfer, high voltage insulation, low exotherm and minimum shrinkage. These compounds transfer heat rapidly, thereby eliminating hot spots and increasing the operating efficiency of most encapsulated devices. The low shrinkage design feature minimizes risk of damage to fragile components.

Typical Applications:

These products are designed for protecting components in applications such as densely packaged power supplies and heat generating components, integrated circuits, power and operational amplifiers, transformers and many types of semiconductors.

Close